Adata SP300 Spezifikationen

Dot Matrix PrinterSP300 SeriesProgrammer’s Manual

– 6 –4. To choose a pattern with a closer alignment of the forward and backwardprinted lines, count from the top down to the desired pattern and press

– 7 –2-1. Interface Specifications1 Data transmission method: Asynchronous serial interface2 Baud rate: Selectable from 150, 300, 600, 1200,2400, 4800

– 8 –2-2. Interface Circuit2-2-1.RS-232C Serial InterfaceInput (RXD, CTS)Output (DTR, FAULT, TXD, RCH, RTS)Fig . 2-1 RS-232C interface circuit2-2-2.Cu

– 9 –2-2-3. RS-422A Serial Interface (option)Input (RD, RS)Output (SD, CS)Fig. 2-3 RS-422A interface circuitABPrinter Host computerABPrinter Host comp

– 10 –14125132-3. Connectors and SignalsRS-232CPin no. Signal nameI/OFunctiondirection1 F-GND — Frame ground2 TXD OUT Transmitted data3 RXD IN Receive

– 11 –20 mA current loop (option)Pin no. Signal nameI/OFunctiondirection9 TTY TXDR — Indicates the ground side of the data signalof 20 mA loop current

– 12 –2-4. Interface ConnectionsThe following is a basic example of interface connections. (For interfaceconnections, refer to the specifications for

– 13 –2-5. Installing the Optional Interface BoardWhen using the optional 20 mA current loop interface or the RS-422A interface,the optional interface

– 14 –2-6. Data Structure2-6-1.DTR modeThis mode is accessed when the DIP switch 3-5 is ON.Signals are controlled using the DTR line as BUSY flag.If a

– 15 –[Paper out]When the “paper out’ detector senses the end of the paper, the printer stopsprinting after printing a maximum of two more lines or on

– 16 –[Framing error]A framing error occurs when SPACE is detected at the stop bit. When a framingerror or a vertical parity error occurs for the data

– 17 –[Paper out]When the “paper out” detector senses the end of the paper, the printer stopsprinting after printing a maximum of two more lines or on

– 18 –[Status][Framing error]A framing error occurs when SPACE is detected at the stop bit. When a framingerror or a vertical parity error occurs for

– 19 –2-6-3. STX-ETX modeThis mode is accessed from whichever DTR mode or X-ON/X-OFF mode.To set this mode, the data buffer must be empty.The host co

– 20 –[Compulsion switch]When pin 6 of the peripheral unit drive circuit connector is set at “HIGH”, statusbit 7 becomes “1”.

– 21 –Sends <ENQ>Receives status byte.Sends <STX>Is the data bufferempty?Is an odd paritycheck?Acquires the exclusive OR of the contentof

– 22 –3-1. Interface SpecificationsThis printer has a parallel interface to communicate with the computer. Theoperating specifications of the parallel

– 23 –74 HC Compatible4.7KW4.7KWSignal Name Circuit ExampleFig. 3-2 Typical interface circuit74 HC Compatible4.7KW100W470pFDATA 1 – DATA 8(To Printer)

– 24 –3-3. Connectors and SignalsPin no Signal nameDirectionFunction1 STROBE IN Signals when data is ready to be read. Signalgoes from HIGH to LOW (fo

– 25 –If any of the following errors is detected while the printer is operating, the printerhalts and ERROR signal turns to “LOW” level.1 Mechanical e

TABLE OF CONTENTS1. CONTROL PANEL ...11-1. Basic Operation ...

– 26 –This printer can print one line of validation printing.5-1. Operating Method5. VALIDATION PRINTING (Models with validation function only)Fig. 5-

– 27 –5-2. Printing FormatPrints one line in 7 × 9 font normal printing.32 columns (from the 5th to 36th columns)Even if the setting for the paper wid

– 28 –6-1. Cutting MethodCuts recording paper into continuous forms connected at only one point remain-ing uncut between adjacent forms.Only one sheet

– 29 –7. CONTROL CODESControl Codes Used for Character SettingControl codesHexadecimalFunction Pagecodes<ESC> “R” n 1B 52 n Select international

– 30 –Control Codes Used for Page LayoutControl codesHexadecimalFunction Pagecodes<FF> 0C Page feed (form feed) 37<ESC> “C” n 1B 43 n Set

– 31 –Control Codes Used for Peripheral UnitsControl codesHexadecimalFunction Pagecodes<ESC> <BEL> n1 n2 1B 07 n1 n2 Adjust drive pulse wi

– 32 –7-1. Control Codes Used for Character SettingFUNCTIONSelect international character setCODE<ESC> “R” nDEFINITION RANGE(1B)H (52)H nOUTLINE

– 33 –FUNCTIONSelect 7 × 9 (half dot) fontCODE<ESC> “M”(1B)H (4D)HOUTLINESelects 7 × 9 (half dot) font.Refer to User’s manual for the maximum nu

– 34 –FUNCTIONCancel expanded character modeCODE<DC4>(14)HOUTLINECancels expanded character mode set by <SO> or <ESC>“W” “1” or <

– 35 –FUNCTIONSelect underline modeCODE<ESC> “-” “1” or <ESC> “-” <1>(1B)H (2D)H (31)H or (1B)H (2D)H (01)HOUTLINEData following thi

7. CONTROL CODES ...297-1. Control Codes Used for Character Setting ...

– 36 –FUNCTIONCancel highlighted print modeCODE<ESC> “5”(1B)H (35)HOUTLINECancels highlighted print mode.FUNCTIONSelect inverted print modeCODE&

– 37 –FUNCTIONSet 1/8-inch line feedCODE<ESC> “0”(1B)H (30)HOUTLINELine feed is set at 1/8-inch after this code is received.FUNCTIONFeed paper n

– 38 –FUNCTIONSet vertical tab positionsCODE<ESC> “B” n1 n2...nk <0>(1B)H (42)H n1 n2...nk (00)HDEFINITION RANGE1 n1 < n2 < n3 <

– 39 –FUNCTIONCancel bottom marginCODE<ESC> “O”(1B)H (4F)HOUTLINECancels bottom margin.FUNCTIONSet left marginCODE<ESC> “1” n(1B)H (6C)H n

– 40 –FUNCTIONSet horizontal tab positionCODE<ESC> “D” n1 n2...nk <0>(1B)H (44)H n1 n2...nk (00)HDEFINITION RANGE1 n1 < n2 < n3...

– 41 –7-4. Control Codes Used for Graphics PrintingFUNCTIONSet 7/72-inch line feedCODE<ESC> “1”(1B)H (31)HOUTLINELine feed is set at 7/72-inch a

– 42 –Set n/216-inch line feed simulation<ESC> “3” n(1B)H (33)H nDEFINITION RANGE1 n 255OUTLINELine feed is set at n/216-inch after this cod

– 43 –m1 m2 m3 m4 m5 m6 m7 m8 m9m10 m11 m12 m13 m14 m15 m16 m17 m18 m19 m20 m21 m22 m23 m24 m25 m26 m27 m28 m29 m30D8D7D6D5D4D3D2D1m21 00111110 3Em22

– 44 –FUNCTION8 dot double density bit imageCODE<ESC> “L” n1 n2 m1 m2...(1B)H (4C)H n1 n2 m1 m2...DEFINITION RANGE1 n1 + 256 × n2 400OUTLINE

– 45 –FUNCTIONSelect vertical expaned character modeCODE<ESC> “h” “1” or <ESC> “h” <1>(1B)H (68)H (31)H or (1B)H (68)H (01)HOUTLINEP

– 1 –1. CONTROL PANEL1-1. Basic Operation1 “ON LINE” switchSwitches the printer between “ONLINE” and “OFF LINE”. When-ever the printer switches betwee

– 46 –7-5. Control Codes Used for Download CharactersFUNCTIONDefinition of download charactersCODEWhen the 7 × 9 (half dot) font is set (default setti

– 47 –FUNCTIONEnable download character setCODE<ESC> “%” “1” or <ESC> “%” <1>(1B)H (25)H (31)H or (1B)H (25)H (01)HOUTLINEEnables th

– 48 –Example of transmitting data(1B)H (26)H (00)H (21)H (23)H (80)H(A0)H (00)H (A0)H (1F)H (A0)H (00)H(A0)H (80)H (98)H (64)H (82)H (01)H(82)H (64)

– 49 –7-6. Control Codes Used for Peripheral UnitsFUNCTIONAdjust drive pulse width for peripheral unit 1CODE<ESC> <BEL> n1 n2(1B)H (07)H n

– 50 –FUNCTIONImmediate drive command for peripheral unit 2CODE<SUB>(1A)HOUTLINEDrives peripheral unit 2. Pulse width is fixed at 200ms witha fi

– 51 –FUNCTIONSet deselect modeCODE<DC3>(13)HOUTLINE(1) When using serial interface printer:This function differs depending on the setting of DI

– 52 –c) If the printer receives a <DC1> n code (n is the DIPswitch controlled address) during the addressablemode (with DIP switches 4-1 to 4-4

– 53 –FUNCTIONEnquiryCODE<ENQ>(05)HOUTLINEThis code is valid when using serial interface printer.Online in STX-ETX mode: The printer sends the s

– 54 –FUNCTIONTrigger auto-cutter drive (Auto-cutting models only)CODE<ESC> “d” “0” or <ESC> “d” <0>(1B)H (64)H (30)H or (1B)H (64)H

– 55 –8.1 U.S.A. & Europe (DIP SW2-1: ON, SW2-2: ON)8. CHARACTER CODE TABLES

– 2 –1-2. Switch Operation (Combined Switch Operation)1 <SELF PRINT TEST> FEED + POWER ON (Turn the power on while holding the FEED switc

– 56 –

– 57 –8.2 IBM Character Set #1 (DIP SW2-1: OFF, SW2-2: ON)

– 58 –

– 59 –8.3 IBM Character Set #2 (DIP SW2-1: ON, SW2-2: OFF)

– 60 –

– 61 –8.4 JAPAN (DIP SW2-1:, OFF, SW2-2: OFF)

– 62 –

– 63 –8.5 International Character Sets

MEMO

– 3 –2 <Hexadecimal dump mode> ON LINE + POWER ON (Turn the power on while holding the ON LINEswitch depressed.)Each of the signals sent

2000.11.30Printed in Japan, 80872005ELECTRONIC PRODUCTS DIVISIONSTAR MICRONICS CO., LTD.536 Nanatsushinnya, Shimizu, Shizuoka,424-0066 JapanTel: 0543-

– 4 –5 <PAGE TOP> (Sprocket-type Only) ON LINE + FEED (Press the FEED button while holding the ON LINEbutton depressed when the printer is

– 5 –1. Enter the Dot Alignment Adjust Mode by turning on the power whilepressing the ONLINE and FEED switches.2. When Dot Alignment Adjust Mode start